Fire-Tite® Offshore Rolling Door is Built for Marine Bulkheads- Classified by U.L. to Withstand Hydrocarbon Pool Fires for 2 Hours
- Offshore Fire Doors Provides Protection Against Rapid Temperature Increase
- Offshore Rolling Overhead Doors are also available in Stainless Steel
- Offshore Fire Doors are built in Accordance with Requirements Specified by Underwriter’s Laboratories Inc.
Alpine’s Offshore Rolling High Rise H-O Fire-Tite® doors are Alpine Fire-Tite® Doors designed for specifically for use in Offshore H-O Rated Marine Bulkheads. The High Rise H-O Fire-Tite® Door provides offshore protection against rapid temperature increases, and is classified by Underwriter’s Laboratories to withstand Hydrocarbon Pool Fires for 2 hours.
Offshore High Rise H-O Fire-Tite® curtains are constructed of galvanized steel in 2 3/4″ flat slats, and can be finished with powder coating or baked enamel finishes. Each offshore rolling door is equipped with a 22 gage steel hood formed to fit the contour of the end brackets and durable ductile iron windlock with 1/4″ semi-solid rivets. Our offshore rolling door supports and brackets are all steel plates no less than 1/4″ thick. Alpine’s Torsion Counterbalance Assembly is state of the art, providing maximum security and ease of use.
Fire Performance Evaluation of the Alpine H-0 Overhead Door Assembly was conducted in accordance with IMO Resolution A.754, (18),
Recommendation on Fire Resistance Tests for A, B, and F Class Divisions and ASTM E1529-93.
The Alpine H-0 Overhead Door and assembly was tested for a total of two hours and 8 minutes and was exposed to continuous fire exposure for a
total of 122 minutes and 15 seconds. The Alpine H-0 Overhead Door maintained its structural integrity by remaining closed for the entire duration of
this fire test.
The test door dimensions were 10’ X 8’ ft. The door was installed in a representative bulkhead section which was constructed in general accordance
with IMO Resolution A.754 (18).
The door edges were stiffened with 2.5” x 2.5” x 1/4” reinforced angles. The exposed face of the bulkhead was insulated to an A-60 rating, provided
by two, 2-in. layers of Delta Marine Board insulation.
ANITI-WARPING BOTTOM BAR EDGE
A specialized bottom bar and steel edge to maximize containment of fuel and oil spills.
SEE CATALOG CUT SHEET LISTED AT THE TOP RIGHT CORNER OF THIS PAGE FOR SPECIFIC DETAILS.
APPLICATION USE
Fire Protection, Oil Rig Platforms, Drilling Platforms, Marine Bulkhead, Chemical Storage Facilities.
BOTTOM BARS
Galvanized, Stainless Steel, Hot Rolled Steel, Powder Coated, Weather Strip, Electric Edge, Single Angle, Double Angle, Slope Bar, Special Cut-Out, Slide Lock, Wedge Lock.
BRACKET PLATES
Hot Rolled A36, Stainless Steel, Galvanized, Powder Coated, Viscous Governor, Oscillating Governor, Fire Drop Charge, Charge Wheel, Motor Prep., Chain Gearing, Thru-Wall Drop Plate, Round Bracket, Square Bracket, Hex Bracket, Single Gear Reducer, Double Gear Reducer.
COUNTERBALANCE ASSEMBLY
Hot Rolled A36, Galvanized, Stainless Steel, Torsion Spring, Kicker, Life Cycle 15M, Life Cycle 17.5 to 400M, Collars, Welded Tabs, Taped Holes, Lock Shaft Collar, Keyed, Bolted.
CURTAIN OPTIONS
Galvanized Steel, Stainless Steel, Galvalume, Prime Painted Galvanized, Powder Coated, Stamped Endlock, Cast Endlocks, Windlock Option, Brass Endlock.
GUIDE MATERIAL
Hot Rolled A36, Stainless Steel, Galvanized Steel, Powder Coated,
Structural Angles, Chain Lock Box, Electric Interlock, Heat Tracing, Tube Mounting.
HOOD/COVER
Galvanized, Stainless Steel, Galvalume, Prime Painted, Powder Coated, Flame Baffle, Lintel Seal, Smoke Lintel Seal, Back Fascia, Tension Cover, Operator Cover, Round, Square, Hex, Side End Cap, Motor Cover, T.O.C. Cover, F.O.C. Cover, F.O.W. Cover.
MATERIAL STYLE
22 Gauge, 20 Gauge,18 Guage.
OPERATION OF DOOR
Offshore Rolling Fire doors may be operated by manual Push-Up, Chain, Motor, Hand Crank, Redi-Master, Redi-Lift, Redi-Tube, Chain Gear Reducer, Redi-Release.
Click Here for UL Labeled Smoke and Draft Control Assemblies
