Fire-Storm – Roller Doors 2017-07-20T14:16:37+00:00

Alpine® Fire-Storm® Roller Doors

Windstorm Resistant Fire Door

 

Product Features

  • Crossbred fire & storm protection roller doors
  • Oversize UL label up to 20’x30′
  • Built in accordance with requirements specified by Underwriters Laboratories Inc.
  • Our hurricane fire shutter is Dade County approved for high wind loads up to 187 mph
Request A Quote

APPLICATION USE
Fire Protection, Hurricane, Retail Storefronts, Warehouses, Malls and Loading Docks.

BOTTOM BARS
Bottom Bars for the Hurricane Fire Shutter can be Galvanized, Stainless Steel, Hot Rolled Steel, Powder Coated, Strip Seal, Pneumatic Edge, Electric Edge, Wireless Edge, Double Angle, Slide Lock, Wedge Lock.

BRACKET PLATES
Bracket Plates for Roll Up Storm Shutters and Roller Doors can be Hot Rolled A36, Stainless Steel, Galvanized, Powder Coated, Viscous Governor, Oscillating Governor, Fire Drop Charge, Charge Wheel, Motor Prep., Chain Gearing, Thru-Wall Drop Plate, Round Bracket, Square Bracket, Hex Bracket, Single Gear Reducer, Double Gear Reducer.

COUNTERBALANCE ASSEMBLY
Assembly for Fusible Link Shutters can be Hot Rolled A36, Galvanized, Stainless Steel, Torsion Spring, Kicker, Cycle 17.5 to 400M, Collars, Welded Tabs, Taped Holes, Lock Shaft Collar, Keyed, Bolted.

CURTAIN OPTIONS
Curatins for the Hurricane Fire Shutter can be Galvanized Steel, Stainless Steel, Prime Painted Galvanized, Powder Coated, Stamped Endlock, Cast Endlocks, Windlock Option.

GUIDE MATERIAL
Guide Material for Roll Up Storm Shutters and Roller Doors can be Hot Rolled A36, Stainless Steel, Galvanized Steel, Powder Coated, Structural Angles, Chain Lock Box, Electric Interlock, Tube Mounting, Pack Out Angle.

HOOD/COVER
The Hoods/Covers for these Fusible Link Shutters and Roll Up Storm Shutters can be Galvanized, Stainless Steel, Prime Painted, Powder Coated, Flame Baffle, Lintel Seal, Smoke Lintel Seal, Tension Cover, Operator Cover, Back Fascia, Round, Square, Hex, Side End Cap, Motor Cover, T.O.C. Cover, F.O.C. Cover, F.O.W. Cover.

MATERIAL STYLE
Hurricane Fire Shutter Material can be 22 Gauge, 20 Gauge, 18 Gauge.

OPERATION OF DOOR
Roller Doors can be Push-up, Chain, Motor, Hand Crank, Redi-Master, Redi-Hoist, Redi-Lift, Chain Gear Reducer, Redi- Release.

Click Here for UL Labeled Shutter Smoke and Draft Control Assemblies

Disclaimer: All data provided on this website is to be used for information purposes only, and is subject to change without prior notice. Alpine shall not be liable for technical or editorial errors or ommisions contained herein, nor for direct, incidental, consequential or any other damages resulting from furnishing, performance, or use of this information, even if Alpine Overhead Doors, Inc. has been advised of the possibility of such damages in advance. See the additional disclaimer in our Terms of Use.

Alpine® Fire-Storm® Fusible Link Shutters

Windstorm Resistant Fire Door

Below you will find comprehensive drawing details for our Roller Doors, Fusible Link Shutters, Rolling Doors, Rolling Fire Doors featuring important operation details for using hand chain, hand crank, or motor operation. Click here to request a quote. AutoCAD drawing details may be selected on the CAD FILES option to the right. The AutoCAD drawings and AutoCAD details for the fusible link shutters comply with 08360, 08400 & 08330 construction specs. The drawing details available for Alpine’s Fire-Shut® also comprises several mounting options, including face mounted to steel, masonry, or between jamb mounted.

Alpine’s Fire-Storm® is a crossbred of fire and storm protection. It is a windstorm resistant fire storm that offers the ultimate protection against hurricanes and fires. It is a combination of the features of the Redi-Storm® and Fire-Tite® models. These Roller Doors, Fusible Link Shutters, Rolling Doors, Rolling Fire Doorsare Dade County approved for high wind loads by Underwriters Laboratories Inc. The fusible link shutters are also MEA approved for fire protection.

To download Details of the Roller Doors, Fusible Link Shutters, Rolling Doors, Rolling Fire Doors (PDF), please click below.

Get Adobe Reader

  • Between Jamb Mounted
  • Not available but may be mounted to I-beam or steel tubes

The Fire-Storm® AutoCAD drawing details are for informational purposes. They may change at any time. The CAD detail and CAD drawing reflect the options that are available to the architects and engineers compiling an AutoCAD drawing to present to contractors.  The AutoCAD detail and AutoCAD drawing for will be updated regularly. Alpine’s Roller Doors, Fusible Link Shutters, Rolling Doors, Rolling Fire Doors and fusible link shutters are built to last.

Alpine’s Engineering team will help you determine the exact roller doors and fusible link shutters that will meet your specifications and requirements. Alpine will guide you through every step with your rolling doors. Alpine will design rolling fire doors that will bring years of usage.

Alpine’s rolling doors and rolling fire doors are tough enough to stand up to a lot of usage. These fusible link shutters are built to last. Call Alpine today to find out which roller doors are right for your building.

Disclaimer: All data provided on this website is to be used for information purposes only, and is subject to change without prior notice. Alpine shall not be liable for technical or editorial errors or ommisions contained herein, nor for direct, incidental, consequential or any other damages resulting from furnishing, performance, or use of this information, even if Alpine Overhead Doors, Inc. has been advised of the possibility of such damages in advance. See the additional disclaimer in our Terms of Use.

Alpine® Fire-Storm® Hurricane Fire Shutter

Windstorm Resistant Fire Doors

To download specifications for this fire and storm door, please click below.

 

Specifications (PDF) Adobe Acrobat

Specifications (DOC) Microsoft Word

Model FIRE-STORM®
Flat Slats
Hurricane Fire Shutter

 

NOTE: For specifications, architects must choose from a variety of options for the fusible link shutters. The standard choice will be shown first in plain text followed by the options shown in [brackets] (Example “Finish: Galvanized [Powder coated] [Baked enamel]”). The specifier must make the appropriate choices and delete the others (Example: “Finish: Powder coated”).

GENERAL

1.01 SUMMARY OF HURRICANE FIRE SHUTTER

A. This section includes: [Manual] or [Electric] operated, automatic closing, fire and storm door.

1. Successfully tested by Architectural Testing Institute (ATI) under Dade County protocols PA 201, PA 202, and PA 203 for a design load of + 60 psf.

2. Provide fire and storm doors with Underwriter’s Laboratories, Inc. (UL) and Underwriter’s
Laboratories of Canada (ULC) label for the fire rating classification. [4 hr.], [3 hr.], [1 ½ hr.], or [3/4 hr.] UL and ULC approved doors to be in accordance with both fire and windstorm resistant standards.

3. Design fire doors to withstand a windload of + 60 psf, 1.5 safety rating (Dade County equivalent to a normal +90 psf rating) for doors up to 20’8” x 30’. Provide compatible analysis certified by a Florida professional engineer for doors over 20’8” x 30’.

4. Manufacturer must be capable of providing certified Net Vertical and Net Horizontal reaction forces imposed on door jambs.

5. Quality manufacturer listed by the Texas Department of Insurance’s Windstorm Resistant Construction Guide and the Texas Windstorm Insurance Association Building Code for Windstorm Resistant Construction.

6. Cycle life: Design a hurricane fire shutter of standard construction for normal use of 10,000 cycles standard [up to 400,000 cycles].

7. Manually resetable drop out mechanism with optional release devices. (For
automatically resettable doors, see specs for Auto Fire-Storm®)

 

B.Hurricane fire shutter Related Sections: Related to this section, but not limited to, the following (based on Master Format 2004):

1. Section 01660 – Product Storage and Handling Requirements.

2. Section 04220 – Concrete Unit Masonry.

3. Section 05120 – Structural Steel.

4. Section 06100 – Rough Carpentry.

5. Section 08310 – Access Doors and Panels.

6. Section 08710 – Door Hardware.

7. Section 09290 – Gypsum Board.

8. Section 09900 – Paints and Coatings.

9. Section 26000 – Electrical.

10. Section 28310 – Fire Detection and Alarm.

 

1.02 REFERENCES FOR FUSIBLE LINK SHUTTERS

A. ASTM A 653/A 653M – Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process of our fire and storm door.

B. ASTM A 36 – Standard Specification for Carbon Structural Steel, Hot Rolled Steel

C. ASTM A 123 – Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

D. ASTM A 312 – Standard Specification for Seamless, Welded, and Heavily Cold Worked
Austenitic Stainless Steel Pipes

E. ASTM A 240 – Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

F. ASTM A 276 – Standard Specification for Stainless Steel Bars and Shapes

G. ASTM A 31 – Standard Specification for Steel Rivets and Bars for Rivets, Pressure Vessels

H. ASTM A 449 – Standard Specification for Quenched and Tempered Steel Bolts and Studs

I. ASTM E 330 – Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference

J. Dade County PA-201, PA-202, PA-203: Large Missile Impact Test, Cyclic Wind Pressure Test, and Uniform Static Air Pressure Test

K. ASCE 7-93 – Standard Minimum Design Loads on Buildings and Other Structures

1.03 SUBMITTALS OF THE FIRE AND STORM DOOR

A. Submit under provisions of Section 01300.

B. Product Data: Provide manufacturer’s standard details and catalog data. Provide installation instructions.

C. Shop Drawings: Furnish shop drawings for architect’s approval. Include elevation, sections, and details indicating dimensions, materials, finishes, conditions for anchorage and support of each door.

D. Submit manufacturer’s recommended operation, troubleshooting, and maintenance instructions.

1.04 QUALITY ASSURANCE FOR HURRICANE FIRE SHUTTER

A. Manufacturer: Rolling doors shall be manufactured by a firm with a minimum of five years experience with fusible link shutters.

B. Fire-Rated Assemblies: Provide all doors with fire resistance rating required to comply with governing regulations which are inspected, tested, listed and labeled by UL, complying with NFPA 80 for class of opening. Provide UL label permanently fasted to each fire door assembly. Door shall be tested under UL10B and ULC10B, and provided with a [4 hour] [3 hr.] [1 ½ hr.] [3/4 hr.] rating. Also Factory Mutual and NY MEA approved.

C. Single-Source Responsibility: Manufacturer shall provide fire and storm door, tracks, motors, and accessories for each type of door. Secondary components shall come from a source acceptable to the manufacturer of the primary components.

1.05 DELIVERY, STORAGE, AND HANDLING OF HURRICANE FIRE SHUTTER

A. Deliver materials in original packaging supplied by manufacturer with intact labels. Store materials away from harmful environmental conditions and construction.

1.06 WARRANTY OF FUSIBLE LINK SHUTTERS

A. Door Warranty: Provide one year written warranty from date of installation against deficiencies due to defects in materials or workmanship. Installer agrees to repair or replace any defects in materials or workmanship.

B. Project Warranty: Refer to Conditions of the Contract for project warranty provisions.

PART 2 – PRODUCTS

2.01 MANUFACTURER OF FIRE AND STORM DOOR

A. Manufacturer: Alpine Overhead Doors, Inc.; 8 Hulse Road Suite 1S, East Setauket, NY 11733. Telephone 800-257-4634 or 631-473-9300. Fax 631-642-0800.

B. Model: FIRE-STORM® Windstorm Resistant Rolling Fire Door

2.02 MATERIALS FOR HURRICANE FIRE SHUTTER

A. Curtain:

1. Slats: Constructed of interlocking, roll-formed 2 ¾” flat slats. (For insulated slats see specs for Fire-Storm® IMB)

a) Material:

i) Galvanized steel, G90 coating exterior (G60 interior), Structural Quality Grade C, as per ASTM A 653/ A 653 M

Finish: Galvanized [Powder coated] [Baked enamel] (Minimum coating
conforming with Coating Designation G-01 is required)

– OR –

ii) ASTM 240 Stainless steel 300 series

Finish: [Mill finish #2B] [#4 satin finish]

 

b) Gauge: (Per manufacturer’s standard)

i) Fire and Storm Door up to 20’8” wide: Minimum 21 gauge as manufacturer standard [20, 18, 16 gauge].

ii) Doors up to 12’ wide: Minimum 22 gauge [20, 18, 16]

 

2. Endlocks and Windlocks:

a) Ductile cast iron, hot-dipped, galvanized endlocks riveted to each end of each slat with four Semi-tubular, Mushroom Head ¼” rivets to prevent lateral movement and to limit slat deflection and bending stress. [Windlocks are dependent on windload and increase resistance to curtain jamming]

3.Fusible link shutters Bottom Bar: Two roll formed steel angles of minimum 2”x2”x1/8”, designed to reinforce curtain bottom. (Size dependent on dimensions per manufacturer’s standard)

a) Material:

i) Galvanized Steel as per ASTM A 653/ A 653 M

Finish: Gray shop prime [Powder Coated] [Baked Enamel]

– OR –

ii) ASTM 240 Stainless Steel 300 Series

Finish: [Mill finish #2B] [#4 satin finish]

 

b) Bolting of hurricane fire shutter:

i) 20’8” wide: ¼” bolts at 15” o.c.

ii) 12’ wide: ¼” bolts at 20” o.c.

c) Weather Stripping: Rubber astragal bolted between bottom angles (Dade County Approved).

 

B. Guides:

1. Guides shall be designed using structural steel angles with a minimum thickness of 3/16”, minimum 1 ¼” slotted connections, and removable bellmouth curtain stops to allow for curtain maintenance without removal of guides. Bellmouth stops shall be flush with guide groove.

a) Angles:

i) 20’8” wide: Wall angle 3 ½ x 3 ½ x 7/16”, inside angle 2 ½ x 2 ½ x 3/8”, outside angle 4 x 3 x ¼”.

ii) 12’ wide: Wall angle 2 ½ x 3 ½ x ¼”, inside angle 2 x 2 ½ x ¼”, outside angle 3 x 3 3/16” min

 

b) Bolting:

i) 20’8” wide: Minimum 5/8” bolts at no more than 9” o.c.

ii) 12’ wide: Minimum 1/2” bolts at no more than 15” o.c.

c) Material for Fusible Link Shutters:

i) ASTM A 36 Carbon Structural Steel

Finish: Gray shop prime coat [ASTM A 123 Galvanized] [baked enamel paint] [powder coated].

– OR –

ii) ASTM 276 Stainless Steel 300 Series

Finish: [Mill finish #2B] [#4 finish satin]

C. Door Support Brackets and Mounting Plates for the fire and storm door:

1. Steel plate not less than 1/4” thick. Provide ball bearings at rotating support points. Bolt plates to wall mounting angles with minimum 1/2″ fasteners. Plate supports counterbalance assembly and forms end enclosures.

a) Material:

i) ASTM A 36 Carbon Steel:

Finish: Gray shop prime coat [ASTM A 123 Galvanized] [Baked enamel paint] [Powder coated].

– OR –

ii) ASTM 240 Stainless Steel 300 Series

Finish: [Mill Finish #2B]

 

D. Counterbalance Assembly: Torsion of the fire and storm door

1. Counterbalance assembly: Steel pipe barrel of a size capable of carrying a curtain load with a maximum deflection of 0.03” per foot of door width. Heat-treated helical torsion springs encased in a steel pipe and designed to include an overload factor of 25% to ensure minimum effort to operate. Sealed and prelubricated high speed ball bearing at rotating support points. Torsion spring charge wheel for applying spring torque and for future adjustments.

a) Material for Hurricane Fire Shutter:

 

i) ASTM A 36 Carbon Structural Steel

Finish: Gray shop prime coat [A 123 Hot-Dip Galvanized]

– OR –

ii) A 312 Stainless Steel 300 Series Finish: Mill finish

 

b) Life Cycle: High Cycle springs designed to satisfy 10m through 400m life cycles. Consult engineering if height exceeds width for any cycle above 20m. (Cycle defined as one time opening and closing of door)

E. Hood:

1. 24 gauge steel. Formed to fit the contour of the end brackets with reinforced top and bottom edges. Provide support bracing for fusible link shutters wider than 20 feet at every 10 feet to prevent excessive sag. Fasten with minimum ¼” bolts at 10” o.c.

2. Shape: Hexagon [square] [round]

3. Material:

a) Galvanized Steel as per ASTM A 653/ A 653 M

Finish: [Baked enamel paint] [Powder coated]

– OR –

b) ASTM 240 Stainless Steel 300 Series:

Finish: [Mill finish #2B] [#4 satin finish]

4. [Fascia]: Galvanized [Stainless Steel], provided where areas behind door hood are open.
Materials and finish same as hood.

F. Locking of Hurricane fire door:

1. Provide padlockable slide locks for latching and locking door on coil side bottom bar at each jamb extending into slots in guides. (Electric Interlocks recommended with motorized doors only)

2. Manual chain hoist: Provide padlockable chain keeper on guide.

2.03 OPERATION OF FUSIBLE LINK SHUTTERS:

A. Opening/Closing: Manual push-up [Manual hand chain] [Manual hand crank] [Motor Operator].

B. Automatic closure is activated by fusible link [Fire Door Release Device].

C. [Manual hand chain]:

1. Provide chain hoist operator with endless steel chain, chain pocket wheel and guard, geared reduction unit, and chain keeper secured to guide.

D. [Manual hand crank]:

1. Provide crank hoist operator including crank gear box, steel crank drive shaft and geared reduction unit. Fabricate gear box to completely enclose operating mechanism and be oil-tight.

E. [Motor Operators]:

1. Choose ONE:

a) Medium-Duty, Alpine® Model Redi-Hoist™ driven by efficient V-belt primary
drive with chain/sprocket secondary. Maximum ½ hp. For use on doors up to 10’ x 10’.

– OR –

b) Industrial-Duty, Alpine® Model Redi-Lift™ driven by heavy-duty V-belt with
chain/sprocket secondary reduction. Optional auxiliary chain hoist. Maximum 1 hp. For use on fire and storm doors up to 12’ x 12’.

– OR –

c) Heavy Industrial-Duty, Alpine® Model Redi-Master™ driven by heavy-duty worm gear in oil bath reduction. Standard auxiliary chain hoist. Standard ½ hp (maximum 3 hp)

2. [Sensing Edges] (For double angle bottom bar): For motorized doors, sensing edges allow door to go up in case of obstruction. [Pneumatic Edge] [Electric Edge] [Wireless Edge].

a) Colors: Gray [Yellow] [Black] [White] [Yellow with black stripes]

F. Release Devices for Hurricane Fire Shutter:

1. Fusible link with chain system:

a) Activation: Melting of fusible link at 165° Fahrenheit. When automatic closing is activated, chain shall disengage causing fusible link shutters to close.

b) Closing speed controlled by Integral Oscillating governor [Viscous governor].

c) Average closing speed: No less than 6” per second and not more than 24” per second as per NFPA 80 Section 6, paragraph 4.1.5.

 

2. [Redi-Release™ Release Devices]: Electric Fail-Safe devices used in conjunction with fusible link. [Smoke detector] Choose ONE from either standard models or SS class:

a) Class 1: Manually operated system that can be tied into most fire alarm systems.

– OR –

b) Class 2: All the features of Class 1, with the additional capability to allow motor operation. If operator is chosen, an electrical edge is recommended.

– OR –

c) Class 3: All the features of Class 2 with the addition of standard Alpine Control Panel and Standard Electric Safety Edge. Allows door to automatically go up in case of an obstruction.

– OR –

d) Class 4: All the features of Class 3 with the addition of the Alpine Uninterrupted Power Supply (Battery backup) that is self-activating during a power outage.

– OR –
e) SS Class Model A: Includes independently adjustable delays of 10 seconds on alarm activations (10 sec. max. adjust) and 10 seconds on power loss (30 sec. max. adjust) with a hold/release rating of 40 lbs.

f) SS Class Model B: All the features of model A with:

i) The hold open/release device shall recognize that the door is in the closed position and where motor driven, be capable of sensing that power is available to the motor. The device may be wired to close on alarm.

ii) [Audible and visual annunciators]: To operate during alarm closing cycle.

g) SS Class Model B2: All the features of model B with:

i) 72-hour battery backup with low/no battery logic sounder.

ii) Sounder/Strobe annunciator: To sound during closure due to alarm or power loss.

h) SS Class Model C: All the features of model B2 with:

i) Bottom bar sensing edge.

ii) Remote test plate.

2.04 Mounting:

1. Interior face mounted on prepared opening.

2. Interior mounted between jambs and under lintel in a prepared opening.

3. Exterior face mounted on prepared opening.

2.05 Fire Ratings for Fusible Link Shutters:

1. Underwriter’s Laboratories:

Fire and storm door will be constructed to conform within requirements specified by Underwriters
Laboratories, Inc. (UL) and Underwriter’s Laboratories of Canada (ULC). Doors are automatic and self-closing, Class (A) (B) (C) (D) or oversized certificate.

4 hour – Approved for doors with openings not exceeding 162 sq. ft. in area.

Class (A) – 3 hour approved for doors in dividing fire walls with openings not exceeding 120 sq. ft. in area

Class (B) – 1 ½ hour approved for doors, in vertical shaft openings not exceeding 120 sq. ft. in area.

Class (C) – ¾ hour approved for doors in corridor or room-partition opening not
exceeding 120 sq. ft. in area.

Class (D) – 1 ½ hour approved for doors in exterior wall opening not exceeding 120 sq. ft. in area.

The oversize Certificate is authorized for a hurricane fire shutter for the protection of
openings in fire walls, vertical shafts, and exterior walls where the area exceeds 120 square ft., or for openings in the above locations when width or height exceeds 12 ft. The maximum dimensions for doors for standard fire protection provided with the

Oversize Door Certificate are not to exceed 56 ft. in width and 24 ft. in height.

2. Factory Mutual.

3. New York Materials, Equipment and Acceptance Division (MEA).

PART 3 – EXECUTION

3.01 EXAMINATION

A. Verify that dimensions are correct and project conditions are in accordance with manufacturer’s installation instructions; do not proceed with installation until unacceptable conditions have been corrected.

3.02 INSTALLATION OF HURRICANE FIRE SHUTTER

A. Install units in accordance with manufacturer’s instructions.
B. Ensure that units are installed plumb and true, free of warp or twist, and within tolerances specified by manufacturer for smooth operation.
C. Preparation for opening and installation of fire door to be in strict compliance with NPFA-80.

3.03 FIELD TESTING OF FIRE AND STORM DOOR
A. Test doors for regular operation and automatic closing. Proper authorities having jurisdiction must witness test and sign Drop Test Form.

3.04 DEMONSTRATION OF FUSIBLE LINK SHUTTERS
A. Instruct the Owner’s personnel in correct operation and maintenance of units.

3.05 ADJUST AND CLEAN
A. Clean units in accordance with manufacturer’s instructions.
B. Restore slight blemishes in finishes in accordance with manufacturer’s instructions to match original finish. Remove and provide new units where repairs are not acceptable to the Architect.

Disclaimer: All data provided on this website is to be used for information purposes only, and is subject to change without prior notice. Alpine shall not be liable for technical or editorial errors or ommisions contained herein, nor for direct, incidental, consequential or any other damages resulting from furnishing, performance, or use of this information, even if Alpine Overhead Doors, Inc. has been advised of the possibility of such damages in advance. See the additional disclaimer in our Terms of Use.

Alpine® Redi-Release®

For Use with Fire-Tite®, Fire-Shut® and Fire-Storm® Doors

Fire Door Release, Release Devices, LM90 Model - Optional Features

The Solid State Securities time delay fire door release device is an optional feature for your fire resistant doors. Alpine® Redi-Release® is normally energized as a fail-safe device for fire doors, and incorporates state of the art electronic security control circuitry.

The Redi-Release series release devices are the ideal safety option for fire resistant doors. These devices are able to respond to emergency conditions generated by manual or automatic  initiating devices that are normally closed, and are designed to be used in conjunction with a temperature fuse link system. The Test-Release device features include time delay on alarm and power loss, motor voltage sensing, form C output, proximity/door edge input and trouble diagnostic capabilities. Check model label to be installed to verify applicable features.

CAUTION: As with all releasing device systems, maximum fire protection is provided when installed in accordance with factory specifications and used with fuse link systems. Fail-safe operation can only be provided when input power is applied.

LiftMaster Professional

For Motorized Doors – Electro-Mechanical OperatorsFire Door Release, Release Devices, LM90 Model - Optional Features

The AFCB fire door release device is designed to be used in conjunction with a standard commercial door operator to provide a fully automated door closing system. For use with motorized doors incorporating a reversing electric safety edge. This 120VAC device can power up to four smoke detectors and two horn/strobes or speaker/strobes. This system combines state-of-the-art functionality and advanced features typically found on special-order fire door operators.

LM21AFCB                                                      Owners Manuals

  • UL864 Revision 9 compliant
  • Programmable DIP switch delay setting – either 10, 20, 30 or 60 seconds delay of door release to permit passage clearance
  • Internal battery backup system
  • Motor voltage sensing monitors voltage to the operator and activates a mechanical door release upon loss of power to the operator.
  • Obstruction cycling – works in conjunction with the door’s electrical safety edge, reversing the door if an obstruction is encountered
  • Test keyswitch – permits floor-level testing of the system
  • Model LM21AAFCBVB – is equipped with a voice board to broadcast a prerecorded evacuation message

Non-Motorized Doors

Fire Door Release, Release Devices, LM90 Model - Optional Features

The XP fire door release device provides a fail-safe release mechanism for non-motorized doors and acts as an interface between the door and the fire alarm system. The device required 24VDC power from an approved UL1481 regulated power supply with battery backup, such as a fire alarm control panel. Therefore, installation will require coordination with a fire panel installer.

LM21XP                                                     Owners Manuals

  • UL864 Revision 9 compliant
  • Programmable DIP switch delay setting – either 10, 20, 30 or 60 seconds delay of door release to permit passageway clearance
  • Close door detection – prevents door release if the door is kept in the closed position and eliminates door reset service calls or potential system damage
  • On board diagnostic –  LEDs for early troubleshooting
  • Testing function – allows routine fire door testing without requiring activation of the central alarm system; easy reset function returns the device to a standby state

Non-Motorized Doors with Battery Backup Option

Fire Door Release, Release Devices, LM90 Model - Optional Features

Versatility allows the XPBB fire door release device to operate on 120VAC, 24VAC or 24VDC power sources. Internal battery backup allows the release device to stand alone from the fire alarm system and act independently in the event of a power outage. The system can provide 24VDC power for up to four smoke detectors and two horn/strobes, mounted on either side of the door. Programmable delay settings, close door detection, diagnostic LEDs, localized testing, and reset capabilities are also standard.

LM21XPBB                                                           Owners Manuals

  • UL864 Revision 9 compliant
  • Programmable DIP switch delay setting – either 10, 20, 30 or 60 seconds delay of door release to permit passageway clearance
  • Inputs for normally open –  2-wire or 4-wire detectors and 4-wire normally closed detectors
  • On board diagnostic –  LEDs for early troubleshooting
  • Trouble and alarm relays – for communication with the fire alarm control panel, if required
  • Audible trouble sounder – to indicate when the release device is not operational
  • Testing function – allows routine fire door testing without requiring activation of the smoke detector
  • Model LM21XPBBVB – is equipped with a voice board to broadcast a prerecorded voice evacuation message

3 and 4 Hour approved fusible link shutters for doors in dividing fire walls with openings not exceeding 152 sq. ft. in area. • 1.5 Hour approved for shutter doors in vertical shaft openings not exceeding 152 sq. ft. in area. • .75 Hour approved for roll up storm shutters in corridor or room-partition opening not exceeding 152 sq. ft. in area. • 1.5 Hour approved for doors in exterior wall opening not exceeding 152 sq. ft. in area.

The Fire-Storm® hurricane fire shutter is a combination of the features of Alpine’s Redi-Storm® and Fire-Tite® roller doors models. It is Dade County Approved for high wind loads (up to 187 mph) as well as UL and MEA approved for fire protection. These roll up storm shutters come in galvanized or stainless steel and in a variety of different finishes.

Fire-Storm® curtains for these fusible link shutters are constructed of 2 3/4″ flat steel slats, and can be finished with powder coating or baked enamel finishes. All of these roller doors are equipped with a 22 gauge steel hood formed to fit the contour of the end brackets and durable ductile iron windlock with 1/4″ semi-solid rivets. Our door supports and brackets are all steel plates no less than 1/4″ thick. Alpine’s Torsion Counterbalance Assembly is state of the art, providing maximum security and ease of use. Choose the Alpine operator that best fits your needs.

Rolling Doors, Coiling Doors, Security Doors, Warehouse Doors

2 3/4″ Flat Slat

roll up storm shutters

Double Angle Bottom Bar

fusible link shutters

Structural Guides with Windbar