Redi-Storm Hurricane Doors 2017-12-07T12:11:29+00:00

Alpine® Redi-Storm® Hurricane Doors

Rolling High Impact Doors

 

Product Features

  • Alpine Redi-Storm® hurricane doors protection device
  • Approved by Dade County, Florida to withstand 187 mph winds
  • Torsion counterbalance assembly
  • Available in stainless steel
  • Underwriters Laboratories Inc. reviewed for consumer confidence
Request A Quote

APPLICATION USE
Storefront Door, Office Window, Loading Dock Door, Hurricane.

BOTTOM BARS
The Bottom Bars of these High Impact Doors and Impact Rolling Doors can be Galvanized, Stainless Steel, Hot Rolled Steel, Powder Coated, Weather Strip, Pneumatic Edge, Electric Edge, Wireless Edge, Double Angle, Slide Lock, Wedge Lock.

BRACKET PLATES
These Impact Coiling Doors and Hurricane Doors can be Hot Rolled A36, Stainless Steel, Galvanized, Powder Coated, Stop Lock Bearing, Internal Charge, Charge Wheel, Motor Prep., Chain Gearing, Thru-Wall Drop Plate, Round Bracket, Square Bracket, Hex Bracket, Single Gear Reducer, Double Gear Reducer.

COUNTERBALANCE ASSEMBLY
Impact Coiling Doors and Impact Fire Doors can be Hot Rolled A36, Galvanized, Stainless Steel, Torsion Spring, Life Cycle 17.5 to 400M, Collars, Welded Tabs, Taped Holes, Redi-Tube Motor, Inside Charge, Lock Shaft Collar, Keyed, Bolted.

CURTAIN OPTIONS
Curtains for the Impact Fire Doors and Hurricane Doors can be Galvanized, Stainless Steel, Galvalume, Prime Painted Galvanized, Powder Coated, Stamped Endlock, Cast Endlocks, Windlock Option.

GUIDE MATERIAL
Impact Rolling Doors may be Hot Rolled A36, Stainless Steel, Galvanized Steel, Powder Coated, Structural Angles,“G” Shutter Guide, Weather Stripping, Brush/Smoke Seal, Chain Lock Box, Electric Interlock, Heat Tracing, Tube Mounting, Flat Plate Mount.

HOOD/COVER
Hurricane Doors and High Impact Doors hoods/covers can be Galvanized, Stainless Steel, Galvalume, Prime Painted, Powder Coated, Hood Baffle, Lintel Seal, Back Fascia, Tension Cover, Operator Cover, Round, Square, Hex, Side End Cap, Motor Cover, T.O.C. Cover, F.O.C. Cover, F.O.W. Cover.

MATERIAL STYLE
22 Gauge, 20 Gauge, 18 Gauge.

OPERATION OF DOOR
Hurricane Protection Doors can be Push-up, Chain, Motor, Hand Crank, Redi-Master, Redi-Hoist, Redi-Lift, Chain Gear Reducer, Euro- Drive.

Disclaimer: All data provided on this website is to be used for information purposes only, and is subject to change without prior notice. Alpine shall not be liable for technical or editorial errors or ommisions contained herein, nor for direct, incidental, consequential or any other damages resulting from furnishing, performance, or use of this information, even if Alpine Overhead Doors, Inc. has been advised of the possibility of such damages in advance. See the additional disclaimer in our Terms of Use.

 

Alpine® Redi-Storm®High Impact Doors

Quality Hurricane Approved Doors

AutoCAD drawings and AutoCAD details for hurricane doors may be selected on the CAD FILES option to the right. Click here to request a quote. These high impact doors may be viewed in PDF format below. The AutoCAD drawings and AutoCAD details for hurricane approved doors comply with 08360, 08400 & 08330 construction specs.

The Redi-Storm hurricane approved doors comply with the 08330 construction spec. These hurricane doors are based on nearly 20 years of wind load design experience and are approved by Dade County, Florida to withstand winds up to 187 mph. These high impact doors are also Underwriters Laboratories Inc. reviewed for consumer confidence. For insulated doors or marine doors, select them on the product index at the left side of the screen.

To download details (PDF) of Hurricane Doors, High Impact Doors and Hurricane Approved Doors, please click below.

Hurricane Doors, High Impact Doors, Hurricane Approved Doors

Hurricane Doors, High Impact Doors, Hurricane Approved Doors
Hurricane Doors, High Impact Doors, Hurricane Approved Doors
Hurricane Doors, High Impact Doors, Hurricane Approved Doors

The Redi-Storm® AutoCAD drawings and AutoCAD details are for informational purposes. They may change at any time. The CAD detail and CAD drawing reflect the options that are available to the architects and engineers compiling a drawing of hurricane doors to present to contractors.  The AutoCAD detail and AutoCAD drawing will be updated regularly. Alpine’s high impact doors are built to last!

Call Alpine today to find the hurricane approved doors that are right for you!

Disclaimer: All data provided on this website is to be used for information purposes only, and is subject to change without prior notice. Alpine shall not be liable for technical or editorial errors or ommisions contained herein, nor for direct, incidental, consequential or any other damages resulting from furnishing, performance, or use of this information, even if Alpine Overhead Doors, Inc. has been advised of the possibility of such damages in advance. See the additional disclaimer in our Terms of Use.

Alpine® Redi-Storm® Hurricane Protection Doors

High Stress Rolling Storm Doors

To download Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications please click below.

 

Part Specifications (PDF) Adobe AcrobatSectional Overhead Doors, Hurricane Protection, Overhead Door Specifications

Part Specifications (DOC) Microsoft WordSectional Overhead Doors, Hurricane Protection, Overhead Door Specifications

 

Model REDI-STORM®
Flat Slats
Hurricane Protection doors

NOTE: For Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications for sectional overhead doors and hurricane protection doors, architects must choose from a variety of options. The standard choice will be shown first in plain text followed by the options shown in [brackets] (Example “Finish: Galvanized [Powder coated] [Baked enamel]”). The specifier must make the appropriate choices and delete the others (Example: “Finish: Powder coated”).

GENERAL
1.01 SUMMARY of
Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. This section includes: [Manual] or [Electric] operated Windstorm Resistant Overhead Rolling Door.
1. Successfully tested by Architectural Testing Institute (ATI) under Dade County protocols PA 201, PA 202, and PA 203 for a design load of +/- 60 psf.
2. Design doors to withstand a windload of +/- 60 psf, 1.5 safety rating (Dade County equivalent to a normal +/- 90 psf rating) for doors up to 20’8” x 30’. Provide compatible analysis certified by a Florida professional engineer for doors over 20’8” x 30’.
3. Manufacturer must be capable of providing certified Net Vertical and Net Horizontal reaction forces imposed on door jambs.
4. Quality manufacturer listed by the Texas Department of Insurance’s Windstorm Resistant Construction Guide and the Texas Windstorm Insurance Association Building Code for Windstorm Resistant Construction.
5. Cycle life: Design doors of standard construction for normal use of 10,000 cycles standard [up to 400,000 cycles].
B. Related Sections: Related to this section, but not limited to, the following (based on Master Format 2004):
1. Section 01660 – Product Storage and Handling Requirements.
2. Section 04220 – Concrete Unit Masonry.
3. Section 05120 – Structural Steel.
4. Section 06100 – Rough Carpentry.
5. Section 08310 – Access Doors and Panels.
6. Section 08710 – Door Hardware.
7. Section 09290 – Gypsum Board.
8. Section 09900 – Paints and Coatings.
9. Section 26000 – Electrical.
1.02 REFERENCES for Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. ASTM A 653/A 653M – Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
B. ASTM A 36 – Standard Specification for Carbon Structural Steel, Hot Rolled Steel
C. ASTM A 123 – Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
D. ASTM A 312 – Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes
E. ASTM A 240 – Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
F. ASTM A 276 – Standard Specification for Stainless Steel Bars and Shapes
G. ASTM A 31 – Standard Specification for Steel Rivets and Bars for Rivets, Pressure Vessels
H. ASTM A 449 – Standard Specification for Quenched and Tempered Steel Bolts and Studs
I. ASTM E 330 – Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference
J. Dade County PA-201, PA-202, PA-203: Large Missile Impact Test, Cyclic Wind Pressure Test, and Uniform Static Air Pressure Test
K. ASCE 7-02 – Standard Minimum Design Loads on Buildings and Other Structures
1.03 SUBMITTALS for Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. Submit under provisions of Section 01300.
B. Product Data: Provide manufacturer’s standard details and catalog data. Provide installation instructions.
C. Shop Drawings: Furnish shop drawings for architect’s approval. Include elevation, sections, and details indicating dimensions, materials, finishes, conditions for anchorage and support of each door.
D. Submit manufacturer’s recommended operation, troubleshooting, and maintenance instructions.
1.04 QUALITY ASSURANCE of Sectional Overhead Doors
A. Manufacturer: Rolling doors shall be manufactured by a firm with a minimum of five years experience.
B. Single-Source Responsibility: Manufacturer shall provide doors, tracks, motors, and accessories for each type of door. Secondary components shall come from a source acceptable to the manufacturer of the primary components.
1.05 DELIVERY, STORAGE, AND HANDLING for Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. Deliver materials in original packaging supplied by manufacturer with intact labels. Store materials away from harmful environmental conditions and construction.
1.06 WARRANTY for Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. Door Warranty: Provide one year written warranty from date of installation against deficiencies due to defects in materials or workmanship. Installer agrees to repair or replace any defects in materials or workmanship.
B. Project Warranty: Refer to Conditions of the Contract for project warranty provisions.
PART 2 – PRODUCTS for Overhead Door Specifications
2.01 MANUFACTURER

A. Manufacturer: Alpine Overhead Doors, Inc.; 8 Hulse Road Suite 1S, East Setauket, NY 11733. Telephone 800-257-4634 or 631-473-9300. Fax 631-642-0800.
B. Model: REDI-STORM® Windstorm Resistant Rolling Door
2.02 MATERIALS of Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. Curtain:

1. Slats: Constructed of interlocking, roll-formed 2 ¾” flat slats. (For insulated slats see specs for Redi-Storm IMB® or Redi-Storm IPB®)
a) Material:
i) Galvanized steel, G90 coating exterior (G60 interior), Structural Quality Grade C, as per ASTM A 653/ A 653 M
Finish: Galvanized [Powder coated] [Baked enamel] (Minimum coating conforming with Coating Designation G-01 is required)
– OR –
ii) ASTM 240 Stainless steel 300 series
Finish: [Mill finish #2B] [#4 satin finish] b) Gauge (Per manufacturer’s standard)
i) Doors up to 20’8” wide: Galvanized/Stainless: Minimum 21 gauge as manufacturer standard [20, 18, 16 gauge].
ii) Doors up to 12’ wide: Galvanized/Stainless: Minimum 22 gauge [20, 18, 16] 2. Endlocks and Windlocks:
a) Ductile cast iron, hot-dipped, galvanized endlocks riveted to each end of each slat with four Semi-tubular, Mushroom Head ¼” rivets to prevent lateral movement and to limit slat deflection and bending stress. [Windlocks are dependent on windload and increase resistance to curtain jamming] 3. Bottom Bar: Two roll formed angles of minimum 2”x2”x1/8”, designed to reinforce curtain bottom. (Size dependent on dimensions per manufacturer’s standard)
a) Material:
i) Galvanized Steel as per ASTM A 653/ A 653 M
Finish: Gray shop prime [Powder Coated] [Baked Enamel] – OR –
ii) ASTM 240 Stainless Steel 300 Series
Finish: [Mill finish #2B] [#4 satin finish] b) Bolting:
i) 20’8” wide: ¼” bolts at 15” o.c.
ii) 12’ wide: ¼” bolts at 20” o.c.
c) Weather Stripping: Rubber astragal bolted between bottom angles.
B. Guides of Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications:
1. Guides shall be designed using structural steel angles with a minimum thickness of 3/16”, minimum 1 ¼” slotted connections, and removable bellmouth curtain stops to allow for curtain maintenance without removal of guides. Bellmouth stops shall be flush with guide groove.
a) Angles:
i) 20’8” wide: Wall angle 3 ½ x 3 ½ x 7/16”, inside angle 2 ½ x 2 ½ x 3/8”, outside angle 4 x 3 x ¼”.
ii) 12’ wide: Wall angle 2 ½ x 3 ½ x ¼”, inside angle 2 x 2 ½ x ¼”, outside angle 3 x 3 3/16” min
b) Bolting:
i) 20’8” wide: Minimum 5/8” bolts at no more than 9” o.c.
ii) 12’ wide: Minimum 1/2” bolts at no more than 15” o.c.
c) Material:
i) ASTM A 36 Carbon Structural Steel
Finish: Gray shop prime coat [ASTM A 123 Galvanized] [baked enamel paint] [powder coated].
– OR –
ii) ASTM 276 Stainless Steel 300 Series
Finish: [Mill finish #2B] [#4 finish satin] d) [Weather Stripping]: Vinyl weather seals.
C. Door Support Brackets and Mounting Plates:
1. Steel plate not less than 1/4” thick. Provide ball bearings at rotating support points. Bolt plates to wall mounting angles with minimum 1/2″ fasteners. Plate supports counterbalance assembly and forms end enclosures.
a) Material:
i) ASTM A 36 Carbon Steel:
Finish: Gray shop prime coat [ASTM A 123 Galvanized] [Baked enamel paint] [Powder coated].
– OR –
ii) ASTM 240 Stainless Steel 300 Series
Finish: [Mill Finish #2B] b) [Stop Lock Bearing]: To prevent door from free falling in the event drive operation fails.
D. Counterbalance Assembly: Torsion
1. Counterbalance assembly: Steel pipe barrel of a size capable of carrying a curtain load with a maximum deflection of 0.03” per foot of door width. Heat-treated helical torsion springs encased in a steel pipe and designed to include an overload factor of 25% to ensure minimum effort to operate. Sealed and prelubricated high speed ball bearing at rotating support points. Torsion spring charge wheel for applying spring torque and for future adjustments.
a) Material:
i) ASTM A 36 Carbon Structural Steel
Finish: Gray shop prime coat [A 123 Hot-Dip Galvanized] – OR –
ii) A 312 Stainless Steel 300 Series
Finish: Mill finish
b) Life Cycle: High Cycle springs designed to satisfy 10m through 400m life cycles. Consult engineering if height exceeds width for any cycle above 20m. (Cycle defined as one time opening and closing of door)
E. Hood of Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications:
1. 24 gauge steel [.040” aluminum]. Formed to fit the contour of the end brackets with reinforced top and bottom edges. Provide support bracing for doors wider than 20 feet at every 10 feet to prevent excessive sag.
2. Shape: Hexagon [square] [round] 3. Material:
a) Galvanized Steel as per ASTM A 653/ A 653 M
Finish: [Baked enamel paint] [Powder coated] – OR –
b) ASTM 240 Stainless Steel 300 Series:
Finish: [Mill finish #2B] [#4 satin finish] 4. [Fascia]: Galvanized [Stainless Steel] [Aluminum] provided where areas behind door hood are open. Materials and finish same as hood.
F. Locking:
1. Provide padlockable slide locks for latching and locking door on coil side bottom bar at each jamb extending into slots in guides. (Electric Interlocks recommended with motorized doors only)
2. Manual chain hoist: Provide padlockable chain keeper on guide.
2.03 OPERATION of Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications:
A. Opening/Closing: Manual push-up [Manual hand chain] [Manual hand crank] [Motor Operator].
B. [Manual hand chain]:
1. Provide chain hoist operator with endless steel chain, chain pocket wheel and guard, geared reduction unit, and chain keeper secured to guide.
C. [Manual hand crank]:
1. Provide crank hoist operator including crank gear box, steel crank drive shaft and geared reduction unit. Fabricate gear box to completely enclose operating mechanism and be oil-tight.
D. [Motor Operators]:
2. Choose ONE:
a) Medium-Duty, Alpine® Model Redi-Hoist™ driven by efficient V-belt primary drive with chain/sprocket secondary. Maximum ½ hp. For use on doors up to 10’ x 10’.
– OR –
b) Industrial-Duty, Alpine® Model Redi-Lift™ driven by heavy-duty V-belt with chain/sprocket secondary reduction. Optional auxiliary chain hoist. Maximum 1 hp. For use on doors up to 12’ x 12’.
– OR –
c) Heavy Industrial-Duty, Alpine® Model Redi-Master™ driven by heavy-duty worm gear in oil bath reduction. Standard auxiliary chain hoist. Standard ½ hp (maximum 3 hp)
– OR –
d) Redi-Tube® Tubular Motor with Built-In Manual Handcrank Overdrive. Auxiliary chain hoist not available. For use on doors up to 10’ x 8’.
– OR –
e) Redi-Midget® Gear Reduced Jackshaft Door Operator.
2. [Sensing Edges] (For double angle bottom bar): For motorized doors, sensing edges allow door to go up in case of obstruction. [Pneumatic Edge] [Electric Edge] [Wireless Edge].
a) Colors: Gray [Yellow] [Black] [White] [Yellow with black stripes] 2.04 Mounting of Sectional Overhead Doors: (Select One)
1. Interior face mounted on prepared opening.
2. Interior mounted between jambs and under lintel in a prepared opening.
3. Exterior face mounted on prepared opening.
PART 3 – EXECUTION of Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
3.01 EXAMINATION

A. Verify that dimensions are correct and project conditions are in accordance with manufacturer’s installation instructions; do not proceed with installation until unacceptable conditions have been corrected.
3.02 INSTALLATION of Hurricane Protection Doors
A. Install units in accordance with manufacturer’s instructions.
B. Ensure that units are installed plumb and true, free of warp or twist, and within tolerances specified by manufacturer for smooth operation.
3.03 FIELD TESTING
A. Test doors for regular operation.
3.04 DEMONSTRATION of Sectional Overhead Doors, Hurricane Protection, Overhead Door Specifications
A. Instruct the Owner’s personnel in correct operation and maintenance of units.
3.05 ADJUST AND CLEAN
A. Clean units in accordance with manufacturer’s instructions.
B. Restore slight blemishes in finishes in accordance with manufacturer’s instructions to match original finish. Remove and provide new units where repairs are not acceptable to the Architect.

Disclaimer: All data provided on this website is to be used for information purposes only, and is subject to change without prior notice. Alpine shall not be liable for technical or editorial errors or ommisions contained herein, nor for direct, incidental, consequential or any other damages resulting from furnishing, performance, or use of this information, even if Alpine Overhead Doors, Inc. has been advised of the possibility of such damages in advance. See the additional disclaimer in our Terms of Use.

Based on nearly 30 years of windload design experience, Alpine’s Redi-Storm® high stress and high impact doors are approved by Dade County, Florida to withstand 187 mph winds. The Redi-Storm® hurricane doors are not only ideal for standard protection against theft and vandalism, but they are also designed to withstand pressures of +/- 60 psf. Redi-Storm® high impact doors and hurricane protection doors are engineered and tested to meet or exceed industry standards.

Redi-Storm® hurricane protections doors curtains are available in a standard 2 3/4″ flat slat design, and are upgradeable to Insul-Sound® or Insul-Vapor®. Impact coiling doors can be push-up, hand-crank, hand-chain or motor operated. All operators can be adapted to specific conditions for your impact fire doors and impact rolling doors.Slide locks on bottom bar for these impact coiling doors. No additional hurricane protection doors are needed with our hurricane doors!

Hurricane Doors, High Impact Doors, Hurricane Protection Doors, Impact

2 3/4″ Flat

Hurricane Doors, High Impact Doors, Hurricane Protection Doors, Impact

Double Angle with Rubber Astragal

Hurricane Doors, High Impact Doors, Hurricane Protection Doors, Impact

Structural Guides with Windbar